Synonyms for usb_otg or Related words with usb_otg

gpio              usb_usb              micro_usb              firewire_ieee              otg              pcmcia              bluetooth_usb              serial_ata              sata_gbit              firewire              qsfp              microusb              displayport              broadcom_bcm              usb_connectivity              hdmi_dvi              mini_displayport              dual_link_dvi              uart              usb              toslink              xfp              ethernet_usb              dvi_hdmi              floppy_disk_controller              dssi              odroid              usart              sdio              lvds              bluetooth_edr              cardbus              micro_usb_connector              usb_connector              atapi              passthrough              i²c              sd_mmc              i²c_spi              i²s              localtalk              expresscard              emmc              serial_ata_sata              pci_slot              backplanes              pci_express              dvi              wi_fi_bluetooth              minisd             



Examples of "usb_otg"
USB OTG is only supported by the LTE version of the Samsung Galaxy Tab 4 7.0.
The USB OTG and Embedded Host Supplement to the USB 2.0 specification introduced three new communication protocols:
In other words, USB OTG introduces the concept of a device performing both master and slave roles whenever two USB devices are connected and one of them is a USB OTG device, they establish a communication link. The device controlling the link is called the master or host, while the other is called the slave or peripheral.
I/O PORTS: Mic- in, DC-in, 35mm stereo headphone jack, HDMI 1.3, Output 1080P 1xUSB Host 1.1, Highspeed USB OTG 2.0.
SuperSpeed OTG devices, Embedded Hosts and peripherals are supported through the USB OTG and Embedded Host Supplement to the USB 3.0 specification.
For integrated circuit (IC) designers, an attractive feature of USB OTG is the ability to achieve more USB capabilities with fewer gates.
Note that the USB port uses a mini-B socket instead of mini-AB so that a specially grounded adaptor is required to make full use of the USB OTG client/host auto-switching. Switching can be done in software with regular adaptors, though. USB OTG only provides 100 mA of current (versus full-size USB's 500 mA), so devices with larger current requirements will need to be used with a powered USB hub.
BlackBerry 10.2 implements Host Mode (like in the BlackBerry Z30 handset). Nokia has implemented USB OTG in many of their Symbian cellphones such as Nokia N8, C6-01, C7, Oro, E6, E7, X7, 603, 700, 701 and 808 Pureview. Some high-end Android phones produced by HTC, and Sony under Xperia series also have it. Samsung Android version 3.1 or newer supports USB OTG, but not on all devices.
It measures 18mm x 68,5mm and is the smallest computer-on-module (COM) released by ISEE and features Texas Instruments DM3730. It provides USB OTG, Wifi and Bluetooth on-board and two connectors of 70 pins for extended connectivity.
North American models can be modified to support USB OTG by means of a small internal soldering job, an external modified cable, or a USB transfer box. International firmware is also required.
The LC1813/1913 were released in 2013 and support Android 4.3. Both chips have a 13M pixels ISP. The LC1913 tablet processor has USB-OTG support as an extra feature.
Note that OTG mode is not officially supported due to Micro-B instead of Micro-AB receptacle (when compared to Xperia Z). This results that standard USB OTG cable cannot be used, but
Standard USB uses a master/slave architecture; a "host" acts as the master device for the entire bus, and a USB "device" acts as a slave. If implementing standard USB, devices must assume one role or the other, with computers generally set up as hosts, while (for example) printers normally function as slaves. In the absence of USB OTG, cell phones often implemented slave functionality to allow easy transfer of data to and from computers. Such phones, as slaves, could not readily be connected to printers as they also implemented the slave role. USB OTG directly addresses this issue.
USB On-The-Go, often abbreviated to USB OTG or just OTG, is a specification first used in late 2001 that allows USB devices, such as tablets or smartphones, to act as a host, allowing other USB devices, such as USB flash drives, digital cameras, mice or keyboards, to be attached to them. Use of USB OTG allows those devices to switch back and forth between the roles of host and device. For instance, a mobile phone may read from removable media as the host device, but present itself as a USB Mass Storage Device when connected to a host computer.
USB-OTG is also supported with separately-sold adapters. Some custom ROMs support file systems like NTFS for this storage, so large external hard drives can be used with the phone too. USB mice and keyboards are also supported when connected with an adapter.
There is a High-Speed USB 2.0 USB Micro-B connector provided for data synchronization, mass storage mode (client) and battery charging. The Nokia E6-00 supports for USB On-The-Go 1.3 (the ability to act as a USB host) using a Nokia Adapter Cable for USB OTG CA-157 (not included upon purchase).
The second-generation IOIO boards (known as "IOIO-OTG") contain the following on-board features: As the name suggests, a key feature of this generation is the introduction of USB-OTG, supporting USB master or slave mode. This enables the IOIO to connect to older Android phones that only support USB slave mode, in addition.
USB OTG is a part of a supplement to the Universal Serial Bus (USB) 2.0 specification originally agreed upon in late 2001 and later revised. The latest version of the supplement also defines behavior for an Embedded Host which has targeted abilities and the same USB Standard-A port used by PCs.
The smartphone comes equipped with a 13MP rear camera along with a 5MP front facing camera. The device includes NFC, USB OTG, FM Radio, A-GPS, Bluetooth v4.1, Wi-Fi 802.11 b/g/n/ac and WiFi Hotspot. And the featured sensors are accelerometer, proximity sensor, ambient light sensor, compass, gyroscope, always active fingerprint scanner which also offers some gestures etc.
The IOIO board contains a single PIC MCU that acts as a USB host/USB slave and communicates with an Android app running on a connected Android device. The board provides connectivity via USB, USB-OTG or Bluetooth, and is controllable from within an Android application using the Java API.